SB-1300 Joint Stabilizing Sealer 1 Gallon

0 Rating
$54.99
 Back to: Concrete Restoration Products
NEW FOR 2020!  NOW CONTAINS AN ANTIFUNGAL TO PREVENT MOLD, MOSS & ALGAE ON SEALER FILM

Surebond SB-1300 Joint Stabilizing Sealer is a water-based, single component, epoxy modified, enhancing sealer and joint sand stabilizer. The product can be used both inside and outside, on old and new pavements, sealing paving stones and stabilizing joint sand at the same time. It is the only sealer that can be applied immediately after paver installation, as it is breathable and will not trap the naturally occurring efflorescence. This breathability also decreases freeze-thaw damage and improves surface durability and ease of maintenance. SB-1300 Joint Stabilizing Sealer is solvent free and exceeds all VOC and EPA standards. The product is non-hazardous and has the consistency of water. It is milky white when applied and dries crystal clear, creating a finish that ranges from a matte finish to a satin sheen, depending on the surface. Cured sealer is freeze resistant to -60°F (-51°C) and is stable up to a temperature of 180°F (82°C).

Preparation:

The pavement surface should be clean and free from oil, dust and any loose material. If necessary, use SB-442 General Stain Remover to clean pavers (refer to label and data sheet for guidelines). The paver joints should be completely filled with dry, correctly graded jointing sand with the top level not exceeding the bottom of the chamfer or 1/8” below the surface on non-beveled or tumbled paver surface. A leaf blower is the recommended method to remove dust and fine sand particles from the surface and achieve the optimum joint sand height. Remove all visible efflorescence prior to sealer application; use SB-488 Efflorescence and Rust Remover if necessary (refer to label and data sheet for guidelines). Be sure surface is dry prior to application.

Application Information:

SB-1300 Joint Stabilizing Sealer should be flood coated to the pavement surface using a siphon pump, bulk sprayer or a handheld garden sprayer. Use coverage guidelines to determine the correct amount of material for the project. Flood joints to ensure proper sand penetration and stabilization and use a soft foam squeegee to direct excess material into the joints and to remove all excess material from the surface. Material coverage will depend on surface porosity, joint size and pavement usage. Care should be taken that no excess material is pooled on the surface. Clean all application equipment with water and do not allow material to dry in containers as removal becomes more difficult.

Coverage Per Gallon:

100-150 square feet depending on substrate porosity.

Product Data Shee

Benefits:

  • Fast Drying
  • Breathable
  • Sealer and Joint Sand Stabilizer
  • Environmentaly Friendly
  • Reduces Weeds

Reviews

There are yet no reviews for this product.

Please log in to write a review. Log in

Ask a Question or Post a Picture...
You are a guest ( Sign Up ? )
or post as a guest
Loading comment... The comment will be refreshed after 00:00.
  • We will reply to your comment shortly
    Daniel Katzner · 07/05/2022
    Otherwise, what sealer would you recommend for a voc state in which non slip can be added? Any finish is fine.
    • We will reply to your comment shortly
      The Sealer Store · 07/05/2022
      That depends on what type of surface you have?
      • We will reply to your comment shortly
        Daniel Katzner · 07/05/2022
        I have porcelain pavers by MSI. The pavers are not slippery but the coping around the pool is slippery when wet. I would like to add non-slip and am alright going with a wet look sealer or otherwise to make it work. Thanks.  
        • We will reply to your comment shortly
          The Sealer Store · 07/05/2022
          Sorry, but we do not have a sealer that will work on porcelain.
  • We will reply to your comment shortly
    Daniel Katzner · 07/04/2022
    Can the non slip additive be used with this product in a second coat?
  • We will reply to your comment shortly
    AB · 11/10/2021
    We have been through hell recently with another water based acrylic paver sealer even though it was applied by a professional contracting company. Part of the patio turned white after a year - see photo. Do you feel the Surebond sealer would be a better option (considering its breathable) in case we decide to reseal?
    • We will reply to your comment shortly
      The Sealer Store · 11/10/2021
      All of our paverssealers are breathable.
      • We will reply to your comment shortly
        AB · 11/10/2021
        Gotcha...do you think the white haze was due to moisture being trapped or maybe sand dust? The contractor had used the leaf blower though after re-sanding/before sealing. 
        • We will reply to your comment shortly
          The Sealer Store · 11/11/2021
          Looks like it could have been a poor sealer or poly sand haze if that was used. No way to say for certain.
  • We will reply to your comment shortly
    Terry H · 09/25/2020
    I’m redoing a paver driveway. I pressure washed and blew most of the sand out of the joint along with mildew.
    should I spread the sand And water in first then apply the surebond or do it all in one application eliminating the water?
    thanks
  • We will reply to your comment shortly
    B Stevens · 08/04/2019
    How long should you wait to apply a second coat?
  • We will reply to your comment shortly
    Dan · 06/05/2019
    How long after application is it safe to be exposed to rain?
    • We will reply to your comment shortly
      The Sealer Store · 06/05/2019
      2-3 hours.
      • We will reply to your comment shortly
        Dan · 06/05/2019
        Great. Also is there any risk or problem caused by using a polymeric sand and then this product or should I stick with a standard masonry sand? Thanks again.
  • We will reply to your comment shortly
    Ken Snyder · 11/03/2011
    Is the SB-1300 Joint Sealer to be used instead of water to set polymeric sand joints? Or, after the joints have been set with water? The description on product page is not clear.
Parameters of Product: Concrete and Brick Paver Sealers
Application Method
Both
Interior or Exterior
Exterior
Your Surface Type
Brick Pavers/Stamped/Decorative Concrete
Brands
Surebond
Free Shipping
No
Available Sizes
1 Gallon
Water or Solvent Based
Water Based
Enhance Look
No Wet Look or Gloss