SB-6000 Wet Look Sealer 5 Gallon

$279.99
free shipping with ground services
 Back to: Concrete Sealers

Surebond SB-6000 Wet Look Sealer seals the pavement surface and brightens and enhances the natural colors of the pavingstone with a luxurious, wet look. It is breathable and will not trap the naturally occurring efflorescence, allowing it to be applied immediately after pavingstones are installed (as well as decreasing freeze-thaw damage). The product improves surface durability, enhancing the colors of the pavement and protecting the surface from salt, acid and staining. SB-6000 Wet Look Sealer is a water-based, exterior quality urethane surface sealer. It is solvent-free and exceeds all VOC, EPA, OSHA and FDA standards. SB-6000 Wet Look Sealer has the consistency of water and is milky white when applied; it dries to a clear, wet look on the surface of the pavement. SB-6000 Wet Look Sealer can be used both inside and outside on old and new pavements. Cured sealer is freeze resistant to -60°F (-51°C) and is stable up to a temperature of 180°F (82°C).

Preparation:

The pavement surface should be clean and free from oil, dust and any loose material. If necessary, use SB-442 General Stain Remover to clean pavers (refer to label and data sheet for guidelines). Excess joint sand should be brushed from the surface and the paver joints should be completely filled with dry, correctly graded jointing sand, with the top level not exceeding the bottom of the chamfer or 1/8” below the surface of non-beveled or tumbled paver surfaces. A leaf blower is the recommended method to remove dust and fine particles from the surface to achieve the optimum joint sand height. Remove all efflorescence prior to sealer application. Use SB-488 Efflorescence and Rust Remover if necessary (refer to label and data sheet for guidelines). The surface should be dry prior to application. Previously applied sealer should be stripped. If any product separation should occur, gently agitate container to re-emulsify mixture.

Application Information:

SB-6000 Wet Look Sealer should be rolled or sprayed on the pavement surface using a thick (3/8") paint roller and a handheld garden sprayer. Use coverage guidelines to determine a sufficient amount of material to provide an even, darkened coating. Roll or spray the material so it wets down and saturates all the pores on the surface of the paver. This is best achieved using a handheld garden sprayer and a thick paint roller to coat the surface of each paver, including the chamfers, edges and recessed areas on textured pavers. A second application may be necessary on more porous or older pavements to achieve a consistent and darkened effect. Care should be taken that no excess material is pooled on the surface or in the sand joints of the pavement. Material coverage will depend on the surface porosity and pavement usage. Airless sprayers can be used in lieu of hand held pump sprayers on larger projects. Use the largest nozzle to ensure SB-6000 Wet Look Sealer does not atomize and dry before it hits the pavement surface. The spray should be a low pressure, even mist to wet down the pavement surface. Clean all application equipment with water and do not allow material to dry in containers as removal becomes more difficult.

Coverage Per Gallon:

100-200 square feet depending on substrate porosity.

 

Benefits:

  • Wet Look
  • Fast Drying
  • Breathable
  • Environmentaly Friendly
  • Reduces Water Penetration

Reviews

Friday, 05 May 2017

Water based sealer that will give a rich wet look, without the shine.

The Sealer Store

Please log in to write a review. Log in

Ask a Question or Post a Picture...
You are a guest ( Sign Up ? )
or post as a guest
Loading comment... The comment will be refreshed after 00:00.
  • We will reply to your comment shortly
    DiscoTim · 09/05/2023
    Can you achieve a good result applying this product using a roller instead of a sprayer?
    • We will reply to your comment shortly
      The Sealer Store · 09/05/2023
      Yes, you can roll it. SB-6000 Wet Look Sealer should be rolled or sprayed on the pavement surface using a thick (3/8") paint roller and a handheld garden sprayer.
  • We will reply to your comment shortly
    Greg · 04/24/2023
    I noticed you mentioned that this product is not compatible with clay pavers, yet I found on Surbonds website that it is. Can you clarify as we are looking for a wet look for clay pavers. 

    Thanks
    • We will reply to your comment shortly
      The Sealer Store · 04/24/2023
      While they do state this, we have seen the majority of clay paver applications not seal evenly with any wet look or gloss sealers. Sometimes it works, many times it does not.
  • We will reply to your comment shortly
    Joseph Raspanti · 04/18/2023
    what is the solid content of sb-6000?
  • We will reply to your comment shortly
    Sh · 12/16/2022
    Hello, can SB-6000 be applied to Clay bullnose to enhance the look i.e. give a wet look? I assume I can apply it to concrete pavers and glazed tiles on concrete.  Can you please confirm?
    • We will reply to your comment shortly
      The Sealer Store · 12/16/2022
      You cannot apply it to clay pavers or glazed tiles. 
      • We will reply to your comment shortly
        Sh · 12/19/2022
        Appreciate your reply.. Do you know any sealer that will work with concrete pavers and glazed stone tiles on concrete?

        Also, do you know any solution that will enhance the clay bullnose colors similar to wet look?
        • We will reply to your comment shortly
          The Sealer Store · 12/19/2022
          No sealer will work on glazed stone tiles that we know of. Wet looks sealers dry blotchy on clay pavers. Wet look sealers are for concrete pavers.
  • We will reply to your comment shortly
    Mr reck · 08/06/2022
    Can I apply sb6000 on pavers where Supersealer M has been applied in the past? 
    • We will reply to your comment shortly
      The Sealer Store · 08/07/2022
      Only if the surface is porous meaning water is able to soak in.
  • We will reply to your comment shortly
    MARILENA RAMIREZ · 08/08/2021
    Thanks, I still need to clean the area with the Sure Clean multi-use cleaner.  How long should I wait to apply Supreme shield SB-600 after cleaning the area with the Sure Clean product.
  • We will reply to your comment shortly
    MARILENA RAMIREZ · 08/08/2021
    I asked because the Surebond SB-6000 is milky white when applied, and I had a problem last year on my concrete pavers patio.  I was trying to get a wet look, and I applied this product that was also white and milky, and the pavers looked very nice after application, but turned white a week later after a heavy rain.  I have used numerous products to strip the white spots with no success until now that i used the Surestrip.  It worked well on the white spots, leaving the pavers looking dull, and I thought to apply a wet look again, but I do not want the same thing happens again.  that is why I wanted to know the difference.
    • We will reply to your comment shortly
      The Sealer Store · 08/08/2021
      That was an issue with the quality of the sealer you used prior. Neither of these sealers will turn white.
  • We will reply to your comment shortly
    MARILENA RAMIREZ · 08/07/2021
    Hello:what is the difference between the Supreme Shield SB-600, and the Surebond SB-6000.  It seems that there are both wet look sealers for concrete pavers.  what will be better to apply on a concrete pavers patio.
    • We will reply to your comment shortly
      The Sealer Store · 08/08/2021
      Surebond is water-based and Supreme shield is solvent-based.  Either would work for you.
  • We will reply to your comment shortly
    Jim Twist · 05/17/2021
    What is your best water based paver sealer for Florida sun. Semi gloss sealer we can spray on 5k. driveway. New pavers.
  • We will reply to your comment shortly
    John · 10/06/2020
    Is the Sb 1300 specifically for the polymeric sand joints?
    • We will reply to your comment shortly
      The Sealer Store · 10/06/2020
      It can be used for regular sand or poly sand.
      • We will reply to your comment shortly
        John · 10/06/2020
        Thank. I understand it goes on after the SB-6000 correct? Since I’ll be using the sb6000 do I use the sb1300 for the entire pavers or just on the joints?
        • We will reply to your comment shortly
          The Sealer Store · 10/07/2020
          Entire.
          • We will reply to your comment shortly
            Dan · 10/29/2020
            I was planning to do the same thing. I called SEK and they said not to apply sb-1300 on top of the sb-6000. They said it would only cause issues. They suggested using their PolySweep instead, which I am not a fan of. My pavers have very tight joints and I don’t feel Polymeric sand will be easy to install.
  • We will reply to your comment shortly
    Lee · 07/30/2020
    How long after the installation of a new paver patio do you recommend waiting before applying this product?
    • We will reply to your comment shortly
      The Sealer Store · 07/30/2020
      You can do it right away as long as it is clean and dry.
      • We will reply to your comment shortly
        Lee · 07/30/2020
        Great! Thank you!
  • We will reply to your comment shortly
    Larry haher · 07/14/2020
    How long do you wait between coats?
    • We will reply to your comment shortly
      The Sealer Store · 07/15/2020
      Apply the second as soon as the first coat dries. 1-2 hours should be enough.
  • We will reply to your comment shortly
    Adam · 04/19/2020
    What would you recommend as a general purpose cleaner before applying SB-6000 onto old pavers that have never been treated?
    • We will reply to your comment shortly
      The Sealer Store · 04/19/2020
      Just pressure wash with water.
      • We will reply to your comment shortly
        Adam · 04/19/2020
        Thanks for the quick reply! A few of the pavers have efflourescence, rust, or other random marks/stains on them. What would you recommend for spot cleaning (before applying SB-6000)?
        • We will reply to your comment shortly
          The Sealer Store · 04/19/2020
          There is not a cleaner that works for all. You need a cleaner that is specific to each issue.

          FYI, efflorescence is on new pavers, not old. If you have something white then it is something else and no way to say for certain what will clean it unless you know exactly what the cause of the white.
  • We will reply to your comment shortly
    Shiven · 05/25/2019
    I see white spots in my newly laid cal stone pavers. Cal stone website says that it’s natural process and white spots will go away after some time. If I apply SB-6000 now, will white spots get trapped and will not go away? Should I wait until white spots are gone or can I apply SB-6000 now? Thank you
    • We will reply to your comment shortly
      The Sealer Store · 05/26/2019
      Wait until the efflorescence goes away before applying and sealers.
  • We will reply to your comment shortly
    Ron L · 03/08/2018
    what is the difference between SureBond SB-6000 and Supreme Shield SB-6000?
  • We will reply to your comment shortly
    The Sealer Store · 07/23/2017
    David in Missouri:
    How do your water based sealers compare in durability with your solvent based sealers?

    About the same.
  • We will reply to your comment shortly
    David in Missouri · 07/23/2017
    How do your water based sealers compare in durability with your solvent based sealers?
  • We will reply to your comment shortly
    The Sealer Store · 08/05/2014
    Not designed for plain poured concrete.
  • We will reply to your comment shortly
    Thomas Bickett · 08/05/2014
    Is there any issue using this product on a concrete driveway? Description only talks about concrete pavers. Thanks!
  • We will reply to your comment shortly
    The Sealer Store · 06/23/2014
    Thanks for the review.
Parameters of Product: Concrete and Brick Paver Sealers
Application Method
Both
Interior or Exterior
Exterior
Your Surface Type
Brick Pavers/Stamped/Decorative Concrete
Brands
Surebond
Free Shipping
Yes
Available Sizes
5 Gallon
Water or Solvent Based
Water Based
Enhance Look
Wet Look Only